Prix moyen quotidien
Montants en USD







Key Features
Degrees of Freedom
Weight
Grasp Payload
Repeat Accuracy
Open / Close Time
0.1 N Force Resolution
Dimensions
Communication
Key Features
Degrees of Freedom
Weight
Grasp Payload
Repeat Accuracy
Open / Close Time
0.1 N Force Resolution
Dimensions
Communication
The AGILINK OmniHand 3 Lite-S is a compact dexterous hand — 11 degrees of freedom, 350 g, 1 kg grasp payload and 1D tactile sensing at 0.1 N resolution. Sized for half-scale humanoids, mobile manipulators and data-collection rigs where a full-size hand is too much mass at the end of the arm. Order a single left or right hand, or the matched pair.
Compatible with:
The AGILINK OmniHand 3 Lite-S is the tactile version of AGILINK’s compact dexterous hand. At 140 × 71 × 32.5 mm and 350 g, it is sized for half-scale humanoids, mobile manipulators, teaching rigs and data-collection kits — platforms where a full-size 570 g hand is simply too much mass at the end of the arm.
It runs four active and seven passive degrees of freedom — eleven in total — with 1 kg grasp payload, a 0.5 second open-close cycle and ±0.5 mm repeat positioning accuracy. The Lite-S adds 1D tactile sensing with 0.1 N force resolution, so the hand reports contact rather than guessing at it.
Communication is CANFD and RS485. It is supported under ROS 2 with a Python and C++ SDK, works with Dex-UMI data-collection workflows, and AGILINK publishes an open-source kit around it. Choose a single left or right hand, or order the matched pair.
Mass Where It Hurts Most. Every gram at the end of an arm costs you payload, settling time and battery. At 350 g the Lite-S is the lightest dexterous hand AGILINK makes — roughly 60% of the OmniHand 3 and under 40% of the Ultra.
Eleven DOF in a 140 mm Hand. Four active joints drive seven passive ones, so the hand conforms to object geometry without eleven motors and eleven control loops to tune.
Tactile as Standard. The -S designation is the tactile variant: 1D tactile sensing at 0.1 N resolution. Grip detection, slip response and contact-rich learning all become possible.
Built for Research Platforms. AGILINK positions this hand for half-scale humanoids, mobile manipulators and Dex-UMI rigs, with an open-source kit and ROS 2 support behind it.
The Affordable Way In. It is the least expensive dexterous hand in the AGILINK range by a wide margin — the practical choice for a teaching lab, a data-collection fleet or a first manipulation project.
AGILINK positions the Lite family as the hand for half-scale humanoids — the X2 class. Robo Inc. confirms it is compatible with every X2, A3 and G2 variant, but a full-scale robot may need a mounting adapter at the wrist flange. Confirm the flange, adapter and firmware revision with us at order time.
Need more grip or more fingers? The OmniHand 3 steps up to 16 DOF and 3 kg; the OmniHand 3 Ultra (Tactile) adds 21 active DOF and full-hand tactile sensing. For straight pick-and-place, the OmniPicker 3 gripper delivers 140 N and 5 kg at a fraction of the cost.
Specifications subject to change. All figures reflect AGIBOT manufacturer data current as of November 2026. For the most current information, custom configurations or volume pricing, contact .




AGILINK OmniHand 3 Lite-S Dexterous Hand (with Tactile)
Active degrees of freedom
Weight
Grasp payload
It is sold as a single hand. Choose left or right. Order both for a pair.
Yes. AGILINK lists one-dimensional tactile sensing as an option on the Lite body, resolving to 0.1 N, and the Lite-S is the build that ships with it. AGILINK does not publish a sensor count at this size — the quantified arrays are on the OmniHand 3 Ultra.
AGIBOT positions the Lite family for half-scale humanoids such as the X2. It is listed as compatible with A3 and G2 as well, but those may need a mounting adapter.
ROS 2, Dex-UMI and an open-source kit, over CANFD or RS485, with Python and C++.
A 1 kg grasp, opening and closing in half a second.
Place Your Order
Order directly through our website or use the form below to connect with a product expert first. Delivery timelines depend on model availability, but we ship as quickly as possible — and we’ll keep you updated every step of the way.
Setup & Configuration
Every robot is different. Depending on your selected model and accessories, configuration can be plug-and-play or require a tailored setup. We offer optional demos, consultations, and ongoing support to ensure you’re up and running with confidence.
Get Up and GO
Once set up, your robot is ready to roll. Preloaded actions make it easy to get started, while manual controls and custom routines let you push the limits of what’s possible.
Historique des prix
Un point de données par jour, calculé selon la date d’observation.
Montants en USD
Les moyennes sont calculées par jour UTC à partir de tous les prix d’offre enregistrés.

Agibot · Shanghai, CN
Dès $999

Agibot · Paris, FR
Dès $899

Agibot · Shanghai, CN
Dès $699

Agibot · Los Angeles, US
Dès $6 999

Agibot · Los Angeles, US
Dès $23 999

Agibot · Paris, FR
$23 999

Agibot · Paris, FR
$6 999

Agibot · Paris, FR
$5 999

Agibot · Shanghai, CN
Dès $6 599

Agibot · Eindhoven, NL
Dès 19 900 zł

Agibot · Barcelona, ES
$3 299

Agibot · Paris, FR
$9 550
🍪 Préférences relatives aux cookies
Nous utilisons des cookies pour mesurer les performances. Politique de confidentialité