Precio medio diario
Importes en USD
Descripción
The SparkFun 3-Phase Brushless Motor Driver featuring the TMC6300 from ADI + Trinamic is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal Motor. It can be used to control any 3-phase BLDC or PMSM motor with up to 2A (1.4ARMS) of total drive current. Separate high-side and low-side control of the three half-bridges allows for incredible control of each phase of the motor commutation. The driver also provides temperature and short circuit protections and a diagnostic output to indicate system faults. With a 1.8V regulated power output and an operating voltage down to 2V the TMC6300 is suitable for low-power microcontroller and battery-powered designs (min. two AA/NiMh cells or one to two Li-Ion cells). Our board layout has been designed with the LEDs and labels facing up IC down. This allows the thermal pad on the board to be accessed if cooling is required. Additionally the breakout pins are specially aligned to fit perfectly onto a breadboard and hold the headers more perpendicular to facilitate assembly. Controlling 3-phase motors is not trivial and this board requires six PWM signals to fully control one motor. We've found the Arduino Simple Field Oriented Control library to work well with the board; however there are some hardware limitations such as supported microcontrollers for 6PWM Mode. With additional considerations for integrating position sensors into the feedback control loop.
The SparkFun 3-Phase Brushless Motor Driver featuring the TMC6300 from ADI + Trinamic is a powerful and easy-to-use three-phase motor driver that was designed to control our Brushless Gimbal Motor. It can be used to control any 3-phase BLDC or PMSM motor with up to 2A (1.4ARMS) of total drive current. Separate high-side and low-side control of the three half-bridges allows for incredible control of each phase of the motor commutation. The driver also provides temperature and short circuit protections and a diagnostic output to indicate system faults. With a 1.8V regulated power output and an operating voltage down to 2V the TMC6300 is suitable for low-power microcontroller and battery-powered designs (min. two AA/NiMh cells or one to two Li-Ion cells). Our board layout has been designed with the LEDs and labels facing up IC down. This allows the thermal pad on the board to be accessed if cooling is required. Additionally the breakout pins are specially aligned to fit perfectly onto a breadboard and hold the headers more perpendicular to facilitate assembly. Controlling 3-phase motors is not trivial and this board requires six PWM signals to fully control one motor. We've found the Arduino Simple Field Oriented Control library to work well with the board; however there are some hardware limitations such as supported microcontrollers for 6PWM Mode. With additional considerations for integrating position sensors into the feedback control loop.
Historial de precios
Historial del precio medio
Un punto de datos por día, calculado según la fecha de observación.
$17,77
Los promedios se calculan por día UTC a partir de todos los precios de oferta registrados.
Anuncios relacionados
2S/3S LIPO Battery Charger LBC-10
RoboSavvy
£12,25
Cable Carrier - 10x15mm (0.5m Length)
RoboSavvy
£12,37
Circular Robotics Chassis Kit (Two-Layer)
RoboSavvy
£13,50
EasyDriver - Stepper Motor Driver
RoboSavvy
£13,86
Parallel Gripper Kit A - Channel Mount
RoboSavvy
£14,25
Pi-Camera Frame Set
RoboSavvy
£12,25
RF Shield & Component Kit for HackRF One
RoboSavvy
£14,17
Robot Cable-X3P 180mm 10pcs (Convertible)
RoboSavvy
£12,25
Robot Cable-X4P 180mm (Convertible) 10pcs
RoboSavvy
£12,92
Servo Gear - Futaba (16T; Metal)
RoboSavvy
£13,50
Servo Gear - Hitec (20T; Metal)
RoboSavvy
£13,50
Servo - Generic Continuous Rotation (Micro Size)
RoboSavvy
£13,11