Prix moyen quotidien
Montants en USD
Description
Characteristics Lithium Polymer rechargeable battery for DARwIn-OP only. PCM is embedded to protect from overcharging, discharge, and excess current. Can not be used with the BIOLOID due to connector difference. Battery case/cover and extension cable not included. What's included 1 x LIPO Battery 11.1V 1800mAh LB-012**Charger sold separately. Specifications Weight 106g Dimension 88 x 35 x 26mm Voltage 11.1V Capacity 1800mAh Etc. PCM Embedded (Protection from overcharging, discharge, and excess current) Precautions Do not drop or fold any part of the battery or cables. Do not fold the end of the sutured portion. Do not apply heat, water, or any other liquid on the battery. Do not place it in the microwave, washing machine, or dryer. Do not use damaged batteries. (inflated, deformed, damaged, etc) Do not short circuit the polarity. Do not take the battery apart. When charging, make sure the battery is connected into the correct polarity. Do not charge when the battery is hot. Please charge after it has cooled off. Battery will not charge when connected to the robot. * When the battery is not being used or fully charged, please do not have it connected to a device. STORAGE PRECAUTIONS: Detach the battery from the robot or controller when storing away. When storing away the battery for a long time, make sure the battery life is somewhere around 50%. Do not store it in wet or hot places. Please check your batery state every 4 months. Due to the internal circuit of the battery it will drain some watts over time so if you leave it stored for long periods it may discharge to a point where it cannot be charged again Compatible products Robot : Robotis OP2, TurtleBot Charger : LIPO Battery Charger LBC-10 ** NOT compatible with CM-series controllers. LiPo Battery for DarwinOP and RobotisOP humanoid robots
Characteristics Lithium Polymer rechargeable battery for DARwIn-OP only. PCM is embedded to protect from overcharging, discharge, and excess current. Can not be used with the BIOLOID due to connector difference. Battery case/cover and extension cable not included. What's included 1 x LIPO Battery 11.1V 1800mAh LB-012**Charger sold separately. Specifications Weight 106g Dimension 88 x 35 x 26mm Voltage 11.1V Capacity 1800mAh Etc. PCM Embedded (Protection from overcharging, discharge, and excess current) Precautions Do not drop or fold any part of the battery or cables. Do not fold the end of the sutured portion. Do not apply heat, water, or any other liquid on the battery. Do not place it in the microwave, washing machine, or dryer. Do not use damaged batteries. (inflated, deformed, damaged, etc) Do not short circuit the polarity. Do not take the battery apart. When charging, make sure the battery is connected into the correct polarity. Do not charge when the battery is hot. Please charge after it has cooled off. Battery will not charge when connected to the robot. * When the battery is not being used or fully charged, please do not have it connected to a device. STORAGE PRECAUTIONS: Detach the battery from the robot or controller when storing away. When storing away the battery for a long time, make sure the battery life is somewhere around 50%. Do not store it in wet or hot places. Please check your batery state every 4 months. Due to the internal circuit of the battery it will drain some watts over time so if you leave it stored for long periods it may discharge to a point where it cannot be charged again Compatible products Robot : Robotis OP2, TurtleBot Charger : LIPO Battery Charger LBC-10 ** NOT compatible with CM-series controllers.
Historique des prix
Historique des prix moyens
Un point de données par jour, calculé selon la date d’observation.
$65,74
Les moyennes sont calculées par jour UTC à partir de tous les prix d’offre enregistrés.
Annonces similaires
Beginner Kit for Arduino v3.0
RoboSavvy
£50,75
RC Radio Remote 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)
RoboSavvy
£54
Servo - Hitec HS-646WP (Standard Size)
RoboSavvy
£52,75
SparkFun MicroMod Input and Display Carrier Board
RoboSavvy
£46,09
Robotics Merit Badge Kit
RoboSavvy
£44,25
Serial Miniature OLED Module - 0.96" (uOLED-96-G2 GFX)
RoboSavvy
£43,08
Servo - Hitec HS-755HB (1/4 Scale)
RoboSavvy
£43
SparkFun Experiential Robotics Platform (XRP) Controller - Beta
RoboSavvy
£37,43
Spider Controller with ATmega 2560
RoboSavvy
£40,08
Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)
RoboSavvy
£35,93
Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
RoboSavvy
£41,93
TFMini - Micro LiDAR Module (Qwiic)
RoboSavvy
£35,83