Giá trung bình hằng ngày
Số tiền bằng USD
Mô tả
Gear set for Dynamixel XH430/XM430 – Gear Ratio: 350 : 1. This can be replaced directly when existing gears are worn out. Made with metal and specially coated to strengthen endurance and durability of abrasion. Exclusive magnet for non-contact absolute encoder is attached to the wheel gear. Two ball bearings are included. PACKAGE CONTENTS Gear X430 Gear #1 (for 350) 1 X430 Gear #2 (for 350) 1 X430 Gear #3 1 X430 Wheel Gear 1 Etc Grease 1 Calibration Adaptor (for X430) 1 Ball Bearing 2 Compatible Products DYNAMIXEL X430-350 X430-210 XH430-W350-R O XH430-W350-T O XH430-W210-R O XH430-W210-T O XH430-V350-R O XH430-V210-R O XM430-W350-R O XM430-W350-T O XM430-W210-R O XM430-W210-T O Gear Replacement Procedure Gear Calibration Procedure ** Check the gear ratio of the Dynamixel’s gear to replace. CAUTION Two ball bearings are used for the wheel gears. The bearing of the bottom wheel gear is connected when shipped. When replacing the gear, assemble after connecting the top wheel gear. It is possible to recycle the used bearings, but it is recommended to use new ones because of the performance degradation due to abrasion, debris, etc. Since Dynamixel X series use non-contact magnetic encoders, you will have to calibrate to align the initial position after gear replacement. Use R+Manager2.0 to process the calibration along with the calibration adapter. These are not compatible with DX/RX/MX series.
Gear set for Dynamixel XH430/XM430 – Gear Ratio: 350 : 1. This can be replaced directly when existing gears are worn out. Made with metal and specially coated to strengthen endurance and durability of abrasion. Exclusive magnet for non-contact absolute encoder is attached to the wheel gear. Two ball bearings are included. PACKAGE CONTENTS Gear X430 Gear #1 (for 350) 1 X430 Gear #2 (for 350) 1 X430 Gear #3 1 X430 Wheel Gear 1 Etc Grease 1 Calibration Adaptor (for X430) 1 Ball Bearing 2 Compatible Products DYNAMIXEL X430-350 X430-210 XH430-W350-R O XH430-W350-T O XH430-W210-R O XH430-W210-T O XH430-V350-R O XH430-V210-R O XM430-W350-R O XM430-W350-T O XM430-W210-R O XM430-W210-T O Gear Replacement Procedure Gear Calibration Procedure ** Check the gear ratio of the Dynamixel’s gear to replace. CAUTION Two ball bearings are used for the wheel gears. The bearing of the bottom wheel gear is connected when shipped. When replacing the gear, assemble after connecting the top wheel gear. It is possible to recycle the used bearings, but it is recommended to use new ones because of the performance degradation due to abrasion, debris, etc. Since Dynamixel X series use non-contact magnetic encoders, you will have to calibrate to align the initial position after gear replacement. Use R+Manager2.0 to process the calibration along with the calibration adapter. These are not compatible with DX/RX/MX series.
Lịch sử giá
Lịch sử giá trung bình
Mỗi ngày có một điểm dữ liệu, tính trung bình theo ngày ghi nhận.
$61,88
Giá trung bình được tính theo ngày UTC từ tất cả giá chào bán đã ghi nhận.
Tin đăng liên quan
X430-350 Gear/Bearing Set
Robotis
$67,16
Robotis - Dynamixel MX-64 Gear/Bearing Set
Robotis
£48,75
Robotis - FR04-G101 Set (Metal Gripper for Bioloid & AX Servos)
Robotis
£48,42
Robotis - OpenRB-150 Starter Kit
Robotis
£46,92
Robotis - X430-210 Gear/Bearing Set
Robotis
£46,83
Robot Cable-3P Set BCS-3P01
Robotis
$47,84
MX-28 Gear/Bearing Set
Robotis
$46,69
Gyro Sensor GS-12
Robotis
$47,84
CM-15 Motor
Robotis
$48,19
Robot Cable-WP 1000mm (Extension Cable)
Robotis
$44,05
Dynamixel AX-12W Actuator robotis
Robotis
57,36 €
Dynamixel AX-12A Actuator from robotis
Robotis
57,36 €