Giá trung bình hằng ngày
Số tiền bằng USD
Mô tả
The kit works with all old and new X Carve machines. It also works with machines with the new Z Axis slider upgrade. We no longer mount the laser on the top of the Z gantry and instead mount it on top of the X Controller and run the cables to the gantry. Installation Instructions: CLICK HERE The full kit includes the side mount and everything else in the original X Carve Mounting kit. Purchase this if you bought the magnetic laser shroud version. 1 - Laser Mount: To put in the spindle holder for the laser to connect with magnets. 2 - Laser Mount Screws/Nuts: To mount the laser on the laser mount. 3 - Laser Spindle Mount Screws/Nuts: Longer M4 Screws to be able to place the laser mount in the spindle holder. 4 - Zip Ties: To clean everything up for cabling. 5 - Zip Tie Holder: To place on the Z axis gantry to hold the laser cable in place. 6 - Molex Mini Fit Cable: Input control cable for the laser driver. 7 - Laser and Fan Extension Cables: 10 ft extension cables. Full Mounting Kit Super Easy to Remove When Not Using The Laser Magnetic Mounting Kits for the Quick Connect Laser Shroud. This SIDE mount will go on the side of the Dewalt 611 spindle holder and allow you to keep your entire dust boot on including the bottom portion of the boot.
The kit works with all old and new X Carve machines. It also works with machines with the new Z Axis slider upgrade. We no longer mount the laser on the top of the Z gantry and instead mount it on top of the X Controller and run the cables to the gantry. Installation Instructions: CLICK HERE The full kit includes the side mount and everything else in the original X Carve Mounting kit. Purchase this if you bought the magnetic laser shroud version. 1 - Laser Mount: To put in the spindle holder for the laser to connect with magnets. 2 - Laser Mount Screws/Nuts: To mount the laser on the laser mount. 3 - Laser Spindle Mount Screws/Nuts: Longer M4 Screws to be able to place the laser mount in the spindle holder. 4 - Zip Ties: To clean everything up for cabling. 5 - Zip Tie Holder: To place on the Z axis gantry to hold the laser cable in place. 6 - Molex Mini Fit Cable: Input control cable for the laser driver. 7 - Laser and Fan Extension Cables: 10 ft extension cables. Full Mounting Kit Super Easy to Remove When Not Using The Laser
Lịch sử giá
Lịch sử giá trung bình
Mỗi ngày có một điểm dữ liệu, tính trung bình theo ngày ghi nhận.
$44,93
Giá trung bình được tính theo ngày UTC từ tất cả giá chào bán đã ghi nhận.
Tin đăng liên quan
JTech - X Carve Compatible Front Magnet Mounting Kit
J Tech
£34
J Tech - Shapeoko3 Magnet Mounting Kit
J Tech
£38,83
1.1V 1,000 mAh Battery for TurtleBot3 and Robotis OP - LB-011
Unitree
35,12 €
Dynamixel XL430-W250-T Servo
Robotis
36 €
Bipolar Stepper Motor with Planet Gear Box (18kg.cm)
RoboSavvy
£31,75
Makeblock - mBot Li-polymer Battery
Makeblock
£31,10
Multi-Chassis - 4WD Kit (ATV)
RoboSavvy
£34,50
Ohbot - Camera and mounting brackets for Ohbot
Ohbot
£33,49
Ohbot - Ohbot 2.2 Sensor Pack - light, touch and movement
Ohbot
£33,49
RoboSavvy - USB to RS-485 3Mbps (Dynamixel compatible)
Robotis
£35
Robotis - Dynamixel MX-28 Gear/Bearing Set
Robotis
£32,08
Robotis - OpenRB-150 Tutorial Kit
Robotis
£34,33